Waveshare Core407I Płytka Rozwojowa Z Mikrokontrolerem Stm32F407Igt6

110,00

Opis

Core407I płytka rozwojowa z mikrokontrolerem STM32F407IGT6. Płytka idealnie nadaje się do rozpoczęcia pracy z tym mikokontrolerem lub do wbudowania w Twoje urządzenie jako główny sterownik. Na płytce znajdują się wszystkie podzespoły potrzebne do pracy mikrokontrolera: złącze USB oraz JTAG/SWD służące do programowania oraz debugowania. Wszystkie linie I/O mikrokontrolera zostały wyprowadzone na listwy gold pin o rozstawie 2.00mm.
Opis płyty:

1. STM32F407IGT6: the high performance STM32 MCU which features:

Core: Cortex-M4 32-bit RISC
Feature: a full set of single-cycle DSP instructions
Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz
Operating Voltage: 1.8V-3.6V
Package: LQFP176
Memories: 1024kB Flash, 192+4kB SRAM
MCU communication Interfaces:

3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C
1 x FSMC, 1 x SDIO, 2 x CAN
1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY
1 x 10/100 Ethernet MAC
1 x 8 to 14-bit parallel camera interface

AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)
Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP

2. AMS1117-3.3 (on bottom side), 3.3V voltage regulator 3. MIC2075 (on bottom side), onboard USB power management device 4. Power supply switch, powered from 5Vin or USB connection 5. Boot mode switch, for configuring BOOT0 pin 6. Power indicator 7. VBUS LED 8. Reset button 9. 8M crystal oscillator (on bottom side) 10.32.768K crystal (on bottom side), for internal RTC with calibration 11.JTAG/SWD interface: for debugging/programming 12.USB interface

as DEVICE, used for establishing USB communication between PC and the STM32 development board
as HOST, connecting to USB devices such as USB flash drive through a USB OTG cable

13.MCU pins expander, VCC, GND and all the I/O ports are accessible on expansion connectors for further expansion 14.5Vin pinheader, 5V power supply is required when using USB HOST/OTG 15.USB HOST/OTG jumper

short the jumper when using USB HOST/OTG
open the jumper to disconnect from I/O port

16.VBAT selection jumper

short the jumper to use system power supply
open the jumper to connect the VBAT to external power, such as battery

17.VREF selection jumper

short the jumper to connect VREF+ to VCC
open the jumper to connect VREF+ to other custom pin via jumper wir

Wymiary płyty:

Zestaw zawiera:

Core407I development board x 1
USB type A to Mini-B cable x 1
4-pin wire x 2
2-pin wire x 2

Dodatkowe informacje:
www.waveshare.com/wiki/Core407I

Komputery

32gb ram ddr4, butelka philips avent, blum, hdr co to jest, lycamobile pakiety, wyszukiwanie głosowe, sp nr 10 gorzów, gtx 780 ti, sony xperia 1 cena, dysk ssd 256, foto mielec
yyyyy