Waveshare Core407V Stm32F407Vet6

87,50

Opis

Core407V płytka rozwojowa z mikrokontrolerem STM32F407VET6. Płytka idealnie nadaje się do rozpoczęcia pracy z tym mikrokontrolerem lub do wbudowania w Twoje urządzenie jako główny sterownik. Na płytce znajdują się wszystkie podzespoły potrzebne do pracy mikrokontrolera: złącze USB oraz JTAG/SWD służące do programowania oraz debugowania. Wszystkie linie I/O mikrokontrolera zostały wyprowadzone na listwy gold pin o rozstawie 2.54mm.
Opis płyty:

1. STM32F407VET6: the high performance STM32 MCU which features:

Core: Cortex-M4 32-bit RISC
Feature: a full set of single-cycle DSP instructions
Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz
Operating Voltage: 1.8V-3.6V
Package: LQFP100
Memories: 512kB Flash, 192+4kB SRAM
MCU communication Interfaces:

3 x SPI, 3 x USART, 2 x UART, 2 x I2S, 3 x I2C
1 x FSMC, 1 x SDIO, 2 x CAN
1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY
1 x 10/100 Ethernet MAC
1 x 8 to 12-bit parallel camera interface

AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)
Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP

2. AMS1117-3.3 (on bottom side): 3.3V voltage regulator 3. MIC2075 (on bottom side): onboard USB power management device 4. Power supply switch, powered from 5Vin or USB connection 5. Boot mode switch, for configuring BOOT0 pin 6. Power indicator 7. Reset button 8. 8M crystal oscillator 9. 32.768K crystal (on bottom side), for internal RTC with calibration 10. JTAG/SWD interface: for debugging/programming 11. USB connector, used for establishing USB communication between PC and the STM32 development board 12. IO expander (including VCC/GND), all the MCU pins are accessible on expansion connectors for further expansion 13. 5Vin pinheader, 5V power supply is required when using USB HOST/OTG 14. USB jumper

short the jumper to when using USB
open the jumper to disconnect from I/O ports

15. VBAT selection jumper

short the jumper to use system power supply
open the jumper to connect the VBAT to external power, such as battery

16. VREF selection jumper

short the jumper to connect VREF+/VREF- to VCC/GND
open the jumper to connect VREF+/VREF- to other custom pin via jumper wire

Wymiary płyty:

Zestaw zawiera:

Core407V development board x 1
USB type A to Mini-B cable x 1
4-pin wire x 2
2-pin wire x 2

Dodatkowe informacje, dema, schematy:
Wiki: http://www.waveshare.com/wiki/Core407V

Komputery

sklepy manufaktura, karuzela do łóżeczka z projektorem, 45 kielce, telewizory w media expert, sklep lego, suszarki na pranie ogrodowe, bosch mum 5, among sleep, steam dying light, blowek sklep, dla dzieci bajka, cache, outcast
yyyyy