Waveshare Open429I-C Development Board For Stm32F429I

260,00

Opis

Overview
Open429I-C is an STM32 development board designed for the STM32F429IGT6 microcontroller, consists of the mother board and the MCU core boardCore429I.
The Open429I-C supports further expansion with various optional accessory boards for specific application. The modular and open design makes it the ideal for starting application development with STM32 series microcontrollers.

What’s on the mother board

MCU core board connector: for easily connecting the Core429I
USART3 interface: easily connects to RS232, RS485, USB TO 232, etc.
DCMI interface: for connecting camera
Capacitive touch panel interface: for connecting capacitive touch panel
CAN2 interface: for connecting CAN modules
CAN1 interface: for connecting CAN modules
SDIO interface: for connecting Micro SD module, features much faster access speed rather than SPI
ULPI interface: for connecting high-speed USB peripheral (the STM32F429I integrates USB HS controller without any PHY device)
LCD interface 1: for connecting 7inch LCD
ONE-WIRE interface: easily connects to ONE-WIRE devices (TO-92 package), such as temperature sensor (DS18B20), electronic registration number (DS2401), etc.
LCD interface 2: for connecting 4.3inch LCD
I2C2/I2C3 interface: easily connects to I2C peripherals such as I/O expander (PCF8574), EEPROM (AT24Cxx), etc.
SAI1 interface: for connecting audio modules like UDA1380 module
Ethernet interface: for connecting Ethernet modules
USB connector: USB to UART via the onboard convertor PL2303
SPI1/SPI2 interfaces:

easily connects to SPI peripherals such as DataFlash (AT45DBxx), SD card, MP3 module, etc.
easily connects to AD/DA modules (SPI1 features AD/DA alternative function)

I2S2/I2S3/I2C1 interface: easily connects to I2S peripherals such as audio module, etc.
8-bit FMC interface: easily connects to peripherals such as NandFlash
5V DC jack
5V/3.3V power input/output: usually used as power output, also common-grounding with other user board
MCU pins connector: all the MCU I/O ports are accessible on expansion connectors for further expansion
PL2303: USB to UART convertor
LEDs: convenient for indicating I/O status and/or program running state
PL2303 TX-LED / RX-LED
12MHz crystal: for PL2303
Joystick: five positions
WAKE UP button: used as regular button, and/or wake up the STM32 MCU from sleep
USB to UART jumper
LED jumper

short the jumper to connect to default I/Os used in example code
open the jumper to connect to custom I/Os via jumper wires

Button/Joystick jumper

short the jumper to connect to default I/Os used in example code
open the jumper to connect to custom I/Os via jumper wires

What’s on the Core429I

STM32F429IGT6: the high performance STM32 MCU which features:

Core: Cortex-M4 32-bit RISC
Feature: single-cycle DSP instructions
Operating Frequency: 180MHz, 225 DMIPS/1.25 DMIPS/MHz
Operating Voltage: 1.8V-3.6V
Package: LQFP176
Memories: 1024kB Flash, 256+4kB SRAM
MCU communication Interfaces:

6 x SPI, 4 x USART, 4 x UART, 2 x I2S, 1 x SAI, 3 x I2C
1 x FMC, 1 x SDIO, 2 x CAN
1 x LCD-TFT
1 x USB 2.0 HS/FS controller (with dedicated DMA)
1 x USB HS ULPI (external PHY required)
1 x 10/100 Ethernet MAC
1 x 8 to 14-bit camera interface

AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)
Debugging/Programming: supports JTAG/SWD interfaces, supports IAP

IS42S16400J: SDRAM 1 Meg Bits x 16 Bits x 4 Banks (64-MBIT)
AMS1117-3.3: 3.3V voltage regulator
MIC2075: onboard USB power management device
Power supply switch, powered from 5Vin or USB connection
Boot mode selection, for configuring BOOT0 pin
Power indicator
VBUS LED
Reset button
8M crystal
32.768K crystal, for internal RTC with calibration
JTAG/SWD interface: for debugging/programming
USB connector, supports Device and/or Host
MCU pins expander, VCC, GND and all the I/O pins are accessible on expansion connectors for further expansion
5Vin pinheader, 5V power supply is required when using USB HOST/OTG
USB OTG/HOST jumper

short the jumper when using USB OTG/HOST
open the jumper to disconnect from related I/O port

VBAT selection jumper

short the jumper to use system power supply
open the jumper to connect the VBAT to external power, such as battery

VREF selection jumper

short the jumper to connect VREF+ to VCC
open the jumper to connect VREF+ to other custom pin via jumper wire

Note: The Open429I-C supports programming via UART bootloader The Open429I-C does NOT integrate any debugging function, a debugger is required.

JTAG/SWD interfaces
The figure 1, and 2 show the header pinouts of JTAG/SWD interface

Figure 1. JTAG Header Pinout
Figure 2. SWD Header Pinout

Development Resources
The User Guide CD includes development resources listed as follows:

Schematic
Demo code (examples in C, μC/OS-II)
STM32 development software (KEIL etc.)
STM32 datasheets
STM32 development documentations

Note: the capacitive touch screen driver is not provided for the moment.

Package Contains

Open429I-C development board (Mother board and Core Board) x 1
USB type A plug to mini-B plug cable x 1
USB type A receptacle to mini-B plug cable x 1
4-pin 2-pin wires pack x 1
USB power cable x 1
User Guide CD x 1

123456

Photos

Pliki do pobrania:

Core429I-Schematic.pdf
Open429I-C-Schematic.pdf

Komputery

12 12, hades stargard, fotoradar mapa, różowy, i love love moschino, wyposażenie kuchni, akumulator banner opinia, marvel lego, grundig radiomagnetofon, adura, pożyczka przez internet na raty, bosch gws850ce, vega, głośniki bluetooth z radiem, termostat na grzejnik, jak przenieść zdjęcia na kartę pamięci
yyyyy